6.Let's-assemble.md

@@ -2,8 +2,8 @@
 
 # Overview
 
-In this chapter we will focus how to set all parts together, we also call it the marriage a polyamouros one you can say.
-Nacelle, Alternator, Rotor and the Wind Vane are be mounted together. Ét voila the _windkit_ is ready to produce energy. We'll start with the Nacelle and the Alternator Stator.
+In this chapter we will focus on how to put all parts together. We also call it the wedding - a polyamouros one you can say.
+Nacelle, Alternator, Rotor and the Wind Vane are mounted together. Ét voila, the _windkit_ is ready to produce energy. We'll start with the Nacelle and the Alternator Stator.
 
 # Assembly
 
@@ -131,7 +131,7 @@ Important: Place some wood pices between the stator and the rotor to prevent dam
 
 ### Measure the airgap
 
-Measure the airgap -> if to big, disassemble take out washers, add shim washers (DIN 988) to adjust -> iterate
+Measure the airgap -> if too large, disassemble and take out washers, add shim washers (DIN 988) to adjust -> iterate
 
 ![MainAssembly.windkit_21](img/MainAssembly/MainAssembly.windkit_21.png)
 
@@ -153,7 +153,7 @@ Also place the Rotor Front Mounting Plate
 ![MainAssembly.windkit_24](img/MainAssembly/MainAssembly.windkit_24.png)
 ![MainAssembly.windkit_25](img/MainAssembly/MainAssembly.windkit_25.png)
 ![MainAssembly.windkit_26](img/MainAssembly/MainAssembly.windkit_26.png)
-The the inner screw will have a special nut, the Rotor Blade Fastener Slot Nut. The slot nut is placed in the rectangular hole.
+The inner screw will have a special nut, the Rotor Blade Fastener Slot Nut. The slot nut is placed in the rectangular hole.
 ![MainAssembly.windkit_27](img/MainAssembly/MainAssembly.windkit_27.png)
 ![MainAssembly.windkit_28](img/MainAssembly/MainAssembly.windkit_28.png)
 
@@ -164,7 +164,7 @@ Repeat the last steps with the two other blades
 
 ### Measure and center the blades
 
-Measure and write down the distance one tip of the blade to another. After the first measurement, adjust the blades by unscrewing the outer blade fasteners, move the blade and re-tighten the fasteners. Repeat this process until you have a satisfying result.
+Measure and write down the distance of one tip of the blade to another. After the first measurement, adjust the blades by unscrewing the outer blade fasteners, move the blade and re-tighten the fasteners. Repeat this process until you have a satisfying result.
 
 | Distance | 1. Measurement | 2. Mesurement | 3. Measurement |
 | -------- | -------------- | ------------- | -------------- |
@@ -188,7 +188,7 @@ Measure and write down the distance one tip of the blade to another. After the f
 
 ### Attach Vane Mounting
 
-Place the Vane Mounting upright and attach it the the U Bolt Clamps
+Place the Vane Mounting upright and attach it to the U Bolt Clamps
 
 ![MainAssembly.windkit_35](img/MainAssembly/MainAssembly.windkit_35.png)
 ![MainAssembly.windkit_36](img/MainAssembly/MainAssembly.windkit_36.png)